XB430v Setup Guide

Model: XB430v

Version: 1.0

Welcome! Let’s get your device up and running together.
This guide makes setup simple for everyone, covering helpful accessibility resources, what’s in the box, how it looks, and where to begin.

Our Aginet app and web management page also offer accessibility features, such as increasing page contrast, switching to landscape mode and increasing font size. You can enable them during setup to make it much easier to set up your device and adjust settings! For more accessibility guidance, refer to Accessibility Support.

Note: For some models, Accessibility features will be supported by subsequent firmware upgrades.

Now, ready to explore your device and get connected?

Step 1. Learn About Your Device

This section introduces the device’s package contents and appearance, including its ports, buttons, and product label.

1. Unpack Your Device

Your package may include: the device, a power adapter, an Ethernet cable, and installation guides.

Power Adapter: A block-shaped charger with a cord. Plug it into the power port to turn it on.
Ethernet Cable: A thick cable with plastic connectors at both ends. Each connector has a small clip to hold it in place. To use the cable, insert one end to the WAN port on your device until you hear or feel a click and the other end to an Ethernet outlet or a modem. To unplug it, you can press the click and pull it out.

2. Appearance

The device is shaped like a tall, smooth-edged rectangular box with softly rounded corners and it is designed to sit flat on a surface, such as a table or shelf. On one edge, it features LED indicators that show the status of power, signal strength, and connection. On the other edge, it features buttons and ports. It has no external antenna.

Locate the small rubber footpads on the bottom of the device. With the footpads facing down, place the device on a flat surface.

Face directly the side that has recessed rectangular ports. This side is the back panel. The ports and buttons are arranged from bottom to top as follows:

Power Port: In the lower right corner of the back panel. Circular in shape. For connecting the device to a power socket via the power adapter.

PON Port: On the left of the Power Port. A nearly square port. For connecting to the fiber optic cable.

Power On/Off Button: Above the Power Port. A round button. Press this button to power on or off the device. It is pressed down when the device is powered on and pops up when powered off.

WPS/Wi-Fi Button: On the left of the Power On/Off Button. A small, round button. Press to enable the WPS function. Press and hold for more than 2 seconds to enable or disable wireless function.

USB Port: Above the Power On/Off Button. A small flat rectangular slot. For connecting to a USB storage device.

Reset Button: On the left of the USB Port. A small, recessed button that requires a pin to press. Press and hold the button for more than 5 seconds to reset the device to its factory default settings. After a reset, wait about 2 minutes for it to restart.

Phone Port: TEL2 is above the Reset Button and TEL1 is above TEL2. A nearly square port. For connecting to your analog phone.

WAN/LAN Port: The 2.5G WAN/LAN Port is on the right of tel1. A nearly square port. For connecting to your modem, the Ethernet outlet or other internet devices. Used as the WAN or LAN port.

LAN Port: The 4 nearly square ports located closely together. For connecting to your PC or other wired devices. The one on the lower right corner is a 2.5 GbE LAN Port, and the other 3 are GbE LAN Ports.

At the bottom of the device, there is a recessed label. This label includes: the default network name (SSID), the MAC address, PON SN and a QR code for scanning to connect to the default Wi-Fi.

Step 2. Set Up Your Device

1. Position your device. Make sure that the device it is within reach of an AC power outlet and near the fiber optic cable or Ethernet cables for wired devices.

2. Scan the QR code below to download the Aginet app for iOS or Android. The app will walk you through setup.

Note: Please remain online (Wi-Fi or mobile data) throughout the app download and login steps.

Scan the QR code for Aginet

Tip: You can also cable and set up your device with a web browser via https://tplinkmodem.net or

https://192.168.1.1. For detailed information, please refer to the quick installation guide or user guide.

Support

For technical support, replacement services, user guides, and other information about your product model, please visit https://www.tp-link.com/support/